Brownells Italia - Il negozio online del più grande rivenditore di componenti e accessori per armi da tiro, difesa e caccia Italia

EGW
SAVAGE RASCAL CUT FOR WILLIAMS SIGHT PICATINNY SCOPE MOUNT

841370113675 296000612
This mount was designed for use with the Williams FP-GR TK peep sight. The corresponding front sight and block from Williams are: Lyman Globe Front Sight Williams Rear Sight Top of the receiver to the top of the rear sight dovetail is .330" Top of the receiver to the top of the picatinny rail is .45" This rail is ambidextrous. This mount is milled on both sides for bolt clearance on left or right handed models. Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The channel in the center reduces the overall mass of the mount. Also, in many cases, it will not obstruct usage of factory iron sights. EGW's one-piece scope mounts are the obvious choice for hunters and tactical shooters alike. They machine these in their shop using one of their machining centers. After machining, the mounts are tumbled, sand blasted, and Type II anodized for long lasting durability. Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is  sold separately). The entire mount and accessories (from the mounting screws and wrench down to the packaging) are made in the USA.
69.9 69.9 1 EUR
N. prodotto: 296000612
EGW SAVAGE RASCAL CUT FOR WILLIAMS SIGHT PICATINNY BASE 0 MOA
Parti Fabbricante: 41965 841370113675 Questa base è stata progettata per l'uso con il mirino peep Williams FP-GR TK. Il mirino anteriore corrispondente e il blocco di Williams sono: Lyman Globe Front Sight Williams Rear Sight Dalla parte superiore del ricevitore alla parte superiore della scanalatura del mirino posteriore misura .330" Dalla parte superiore del ricevitore alla parte superiore della rotaia Picatinny misura .45" Questa rotaia è ambidestra. La base è fresata su entrambi i lati per consentire il passaggio del carrello di estrazione sia sui modelli destri che su quelli sinistri. Le scanalature trasversali Picatinny si estendono per tutta la lunghezza della rotaia, offrendo al tiratore flessibilità nel montaggio degli anelli per mirino e altri accessori. Il canale al centro riduce la massa complessiva della base. Inoltre, in molti casi, non ostacola l'utilizzo dei mirini in ferro di serie. Le basi monopezzo di EGW sono la scelta ovvia sia per i cacciatori che per i tiratori tattici. Vengono lavorate nel loro laboratorio utilizzando uno dei loro centri di lavorazione. Dopo la lavorazione, le basi vengono sottoposte a processo di vibrofinitura, sabbiatura e anodizzazione di Tipo II per garantire una durabilità prolungata. Installazione: EGW raccomanda un serraggio di 20 inch lbs di coppia e una goccia di loctite blu (loctite è venduto separatamente). L'intera base e gli accessori (dalle viti di montaggio e la chiave fino al packaging) sono prodotti negli USA.
69.9 EUR 3 69,90 € *
Tempi di consegna circa 12-16 giorni.
3 pz. nel magazzino USA
Caratteristiche: Adatto per: Savage Arms Colore: Nero Elevation: 0 MOA Materiale: Alluminio Modello: Rascal Numero di basi: 1 pezzo Tipo: Picatinny Rail

Caratteristiche

Adatto per: Savage Arms Colore: Nero Elevation: 0 MOA Materiale: Alluminio Modello: Rascal Numero di basi: 1 pezzo Tipo: Picatinny Rail Peso della spedizione: 0,091kg Altezza di spedizione: 25mm Larghezza di spedizione: 102mm Lunghezza di spedizione: 229mm

Dettagli dell'elemento

Made in Usa



This mount was designed for use with the Williams FP-GR TK peep sight. The corresponding front sight and block from Williams are: Lyman Globe Front Sight Williams Rear Sight Top of the receiver to the top of the rear sight dovetail is .330" Top of the receiver to the top of the picatinny rail is .45" This rail is ambidextrous. This mount is milled on both sides for bolt clearance on left or right handed models. Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The channel in the center reduces the overall mass of the mount. Also, in many cases, it will not obstruct usage of factory iron sights. EGW's one-piece scope mounts are the obvious choice for hunters and tactical shooters alike. They machine these in their shop using one of their machining centers. After machining, the mounts are tumbled, sand blasted, and Type II anodized for long lasting durability. Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is  sold separately). The entire mount and accessories (from the mounting screws and wrench down to the packaging) are made in the USA.
Newsletter