Brownells Italia - Il negozio online del più grande rivenditore di componenti e accessori per armi da tiro, difesa e caccia Italia

EGW
S&W M&P VORTEX VIPER/VENOM SIGHT MOUNT

841370113934 296000660
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This Mount does not fit: Smith & Wesson M&P C.O.R.E Series (Already optics ready) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE
84.9 84.9 1 EUR
N. prodotto: 296000660
EGW S&W M&P VORTEX VIPER/VENOM SIGHT MOUNT
Parti Fabbricante: 49308 841370113934 Le mire a punto rosso EGW sono progettate per essere installate da sinistra a destra (con la volata rivolta in avanti). La coda di rondine ha una conicità progressiva per permettere un'installazione più semplice. Semplicemente rimuovi la mira posteriore dalla tua pistola e sostituiscila con il supporto EGW per montare la tua mira Vortex Viper/Venom, Burris FastFire o Docter a punto rosso. È possibile rimuovere il supporto e sostituire la mira posteriore in qualsiasi momento. Hardware di montaggio incluso. Istruzioni di installazione Rimuovi la mira posteriore* Installa il Supporto Mira EGW nella coda di rondine Serra la vite di fissaggio (se applicabile) Posiziona la mira a punto rosso sul Supporto Mira EGW (mettendo un piccolo pezzo di carta tra la mira a punto rosso e il supporto mira faciliterà la rimozione e terrà il Loctite lontano dalla mira a punto rosso.) Applica il Loctite blu alle viti di montaggio fornite Serri le viti di montaggio a 15in/lbs 2 Viti a Testa Bombata - Fornite per le mire Vortex Viper e Venom 2 Viti a Testa Piatta - Fornite per le mire Burris FastFire e Docter Le viti incluse con questo supporto richiedono una chiave allen da 5/64'' per l'installazione. La modifica della tua arma da fuoco può annullare la garanzia del produttore. Questo prodotto dovrebbe essere installato e controllato da un armaiolo qualificato. Non si assume alcuna responsabilità per danni o lesioni che possono derivare dall'installazione o dall'uso improprio di questo prodotto. Questo Supporto non è compatibile con: Smith & Wesson M&P C.O.R.E Series (Già predisposte per ottiche) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE
84.9 EUR 2 84,90 € *
Tempi di consegna circa 12-16 giorni.
2 pz. nel magazzino USA
Caratteristiche: Adatto per: Smith & Wesson Colore: Nero Materiale: Alluminio Modello: M&P Shield, M&P Compact, M&P 2.0 Compact, SD9-VE Numero di basi: 1 pezzo Tipo: Tattico

Caratteristiche

Adatto per: Smith & Wesson Colore: Nero Materiale: Alluminio Modello: M&P Compact,M&P Shield,SD9-VE,M&P 2.0 Compact Numero di basi: 1 pezzo Tipo: Tattico Peso della spedizione: 0,045kg Altezza di spedizione: 25mm Larghezza di spedizione: 76mm Lunghezza di spedizione: 140mm

Dettagli dell'elemento

Made in Usa



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This Mount does not fit: Smith & Wesson M&P C.O.R.E Series (Already optics ready) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE
Newsletter