Brownells Italia - Il negozio online del più grande rivenditore di componenti e accessori per armi da tiro, difesa e caccia Italia

EGW
DESERT EAGLE PRE 2017 VORTEX VIPER/VENOM SIGHT MOUNT

841370115716 296000655
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Please take note to the Pre 2017 and Post 2017 differences. Pre 2017 rear shelf behind the dovetail is .187"" and Post 2017 is .120".
84.9 84.9 1 EUR
N. prodotto: 296000655
EGW DESERT EAGLE PRE 2017 VORTEX VIPER/VENOM SIGHT MOUNT
Parti Fabbricante: 49303 841370115716 I mirini red dot EGW sono progettati per essere installati da sinistra a destra (con la volata rivolta in avanti). Il coda di rondine ha una conicità progressiva per facilitare l'installazione. Semplicemente rimuovi il mirino posteriore dalla tua arma e sostituiscilo con il supporto EGW per montare il tuo mirino Vortex Viper/Venom, Burris FastFire o Docter red-dot. Non sono richieste modifiche. Puoi rimuovere il supporto e rimettere il tuo mirino posteriore in qualsiasi momento. Materiale di montaggio incluso. Istruzioni per l'installazione Rimuovi il mirino posteriore* Installa il Supporto Mirino EGW nella coda di rondine Serra la vite di fissaggio (se applicabile) Posiziona il mirino red dot sul Supporto Mirino EGW (mettere un piccolo pezzo di carta tra il mirino red dot e il supporto mirino faciliterà la rimozione e terrà il Loctite lontano dal mirino red dot.) Applica il Loctite blu alle viti di montaggio fornite Serra le viti di montaggio a 15in/lbs 2 Viti a Testa Bombata - Fornite per i mirini Vortex Viper e Venom 2 Viti a Testa Piatta - Fornite per i mirini Burris FastFire e Docter Le viti incluse con questo supporto richiedono una chiave esagonale da 5/64'' per l'installazione. Si prega di notare le differenze tra i modelli Pre 2017 e Post 2017. Il ripiano posteriore Pre 2017 dietro la coda di rondine è di .187" e il Post 2017 è di .120".
84.9 EUR 0 84,90 € *
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Caratteristiche: Adatto per: Magnum Research Colore: Nero Materiale: Alluminio Modello: Desert Eagle Numero di basi: 1 pezzo Tipo: Tattico

Caratteristiche

Adatto per: Magnum Research Colore: Nero Materiale: Alluminio Modello: Desert Eagle Numero di basi: 1 pezzo Tipo: Tattico Peso della spedizione: 0,045kg Altezza di spedizione: 25mm Larghezza di spedizione: 76mm Lunghezza di spedizione: 140mm

Dettagli dell'elemento

Made in Usa



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Please take note to the Pre 2017 and Post 2017 differences. Pre 2017 rear shelf behind the dovetail is .187"" and Post 2017 is .120".
Newsletter