(0) 
Newsletter
M1,
M14,
M1A
Springfield
N. prodotto: 080000185
050806005679 Le maniglie spesse in acciaio offrono la necessaria forza e rigidità per stringere e allentare il dado del soppressore di fiamma sui fucili M1A/M14. I punti delle ganasce indurite garantiscono un ingaggio preciso per eliminare lo stripping delle notches. Le maniche in gomma forniscono una superficie di presa positiva.
Le CASTLE NUT PLIERS di BROWNELLS sono progettate per offrire una soluzione efficace e resistente per l'installazione e la rimozione dei dadi castello sui fucili M1A/M14.
Le maniglie spesse in acciaio forniscono la forza e la rigidità necessarie per stringere e allentare il dado del soppressore di fiamma sui fucili M1A/M14. I punti delle ganasce indurite garantiscono un ingaggio preciso per eliminare lo stripping delle notches. Le manopole in gomma offrono una superficie di presa sicura.
Scopri la qualità e l'affidabilità delle pinze per dadi castello BROWNELLS, un must-have per ogni appassionato di armi e per chi cerca strumenti di alta precisione!
M1,
M14,
M1A
Springfield
Works if you use correctly. 06/05/2018
I used these on a James River armory castle nut that was extremely tight and would not even come loose with the brass punch method and pb blaster. My rifle had the flash hider installed and then the steel face of the flashider that the castle nut tightens forward against was actually peened down against the castle nut then finished over. I assume James river armory does this to accurize the rifle. It was so tight I had to actually clamp my BAD T3 gas cylinder wrench (also purchased here) in a vise while attached to the m-14 gas cylinder and have the rifle resting in a gun cleaning cradle. I firmly grabbed the castle nut with these Brownell pliers and with both hands squeezed them tightly shut and also grabbed the top end of the pliers squeezing them shut here as well (right hand on the handles and left hand on the top squeezing both ends closed at the same time). At the same time, I was holding the pliers closed from both ends I was pushing them rearward tightly into the castle nut grooves so they could not slip or jump out of the grooves and shear the plier teeth or strip the grooves on the castle nut. It was an absolute monster to break loose, but it did so with no damage to pliers or castle nut. Also, again, my rifle was very securely held in place in a gun cradle with a gas cylinder wrench attached and the wrench hung downward from the rifle and secured in a 5" bench vise. There would have been no way to do this without this setup because of the amount of force needed to break this loose. A second person just holding the rifle by hand would have resulted in the rifle just spinning in this persons grasp. I cannot comment on other users who left low ratings without seeing the technique they used with the pliers, but with the amount of force I had to use on this tool I cannot see how it failed for other users unless they need to change up their technique a bit. If I would have just grabbed the pliers by the handles only and tried to twist the nut loose I believe they would have bent or broken. I hope this method helps other users. The reason I took away 1 star is because the handle covers do slip right off and I do believe this tool could be made of thicker steel which would make them live longer. I also used them to re-tighten the castle nut which required just as much torque to line up the Allen screw hole to the castle nut slot and with my same two-handed pushing technique it worked here as well too. As others have said, DO NOT forget to remove the castle nut set screw from the front sight base before removing the castle nut! I would not buy the cheaper version of this brownells sells because the cost savings is negligible.
Worked perfectly 08/04/2018
These pliers worked perfectly to remove and install the castle nut on my m1a. As others have stated don't forget the locking screw and use some penetrating oil when removing the nut.
Si è verificato un errore durante il caricamento di questo contenuto. Aggiorna la pagina per continuare. Se il problema persiste, contatta il nostro servizio clienti.
in Brownells Italia, la tua destinazione per qualsiasi prodotto relativo alle armi. Con le nostre radici in una genuina passione per le armi ti porteremo in una ineguagliabile selezione di parti d'arma, accessori per armi, attrezzature da costruttore, cannocchiali e puntamenti olografici con la nostra conoscenza ed esperienza.
Qualunque prodotto tu stia cercando per mantenere, riparare o migliorare la tua arma, abbiamo quello che ti occorre.
Da tiratori, per tiratori
Noi condividiamo il tuo entusiasmo e sappiamo esattamente cosa ti occorre perchè siamo parte della tua stessa comunità.
Una immensa selezione di prodotti
Dall'essenziale al prodotto esclusivo, trovi tutto nelle stesso posto.
Il nostro connubio tra tradizione e innovazione
Acquista con la comodità della tecnologia moderna, supportata da una esperienza storica.
Sfoglia il nostro catalogo e scopri perché siamo il nome di fiducia negli sport di tiro e nella caccia.
© 2025 Brownells Italia
Part of the Brownells Europe Group
Visualizzazione classica
Visualizzazione mobile
Aiuto e contatti
