Il Carrello è vuoto.

Carrello

0364 1955 195

Iscriviti alla Newsletter

Z-M WEAPONS
AR-15/M16 ACCU-WEDGE

993150100

Instantly Tightens Loose Upper & Lower Receivers

Helps promote better accuracy by making the upper and lower receiver fit tighter. Open upper receiver; drop this long-wearing, rubber wedge into the rear of the lower, behind the push pin. Absolutely no modifications required.

SPECS: High-density, thermo-plastic rubber, ½" (12.5mm) long.

Altro...

Stringe immediatamente sciolti ricevitori superiore & inferiore

Aiuta a promuove la migliore precisione rendendo il ricevitore superiore e inferiore in forma più rigorosa. Ricevitore superiore aperto; rilasciare questa lunga durata, il cuneo di gomma nella parte posteriore inferiore, dietro il perno di Spinta. Assolutamente nessuna modifica necessaria.

Specifiche: in gomma ad alta densità, termo-plastica, ½"(12.5 mm) lungh.

Altro...

Punteggi dei clienti per Z-M WEAPONS ACCU-WEDGE

Numero di punteggi: 17
Da brownells.com: 17
Punteggio medio: 4

Really tightens things up! (14/09/2009)

Makes upper and lower assemblies extremely snug fitting. Extra pressure is needed to close the take down pin. I wouldn't try "snapping" the upper group to facilitate mating the assemblies. The wedge would appear to decrease the rate of wear caused by pivot and take down pins jarring their receiver hole during extended shooting sessions. Trimming is NOT recommended.

No brainer-- get it!!! (31/10/2009)

Why are you wasting time reading this review? Just get it!!! It's about the only way you're going to tighten that upper down, and at [$], why argue? It works way better than the JP tensioner that costs 7 times more. If it doesn't tighten enough for your taste, all you have to do is put a spacer underneath it, and you're back in business.

DOES NOT WORK WITH RRA and S&W AR15 (19/12/2009)

It was questionable when I ordered the wedge if it would work with my Rock River Arms Elite Comp. I thought maybe it would fit in my Smith and Wesson M&P 15 but that's not the case as well. Don't order this brand of Accuwedge if you own one of the two ARs I mentioned.

Accu Wedge will not work on RRA ARs (06/02/2010)

I purchased an Accu Wedge to use on my RRA AR15 that has a slight play between upper and lower. When Accu Wedge is installed, it obstructs the closing of the upper and lower. I finally used a razor blade to trim bottom of wedge so it would fit. With almost 90% of base cut away, it finally allowed a tight fit but this wedge is not universal. It may work on other brands fine.

Accu-Wedge (22/05/2010)

I have been using an ACCU-Wedge in my COLT HBAR II competition carbine for twelve years. I have used in on military ranges, competition ranges and even in a hunting environment. It works perfectly in my Colt HBAR II and in government issue M-4/M-16s, can't comment on X brands as I have no experience with them. When the ACCU-Wedge was first offered, Colt pretty well owned the AR-15 market, so obviously, that's what it was designed for. I don't quite understand complaints where buyer's and users give lower ratings because they had to trim or make adjustments. By having to do so, you now can now easily (and best of all, cheaply) fall into the custom category, instead of the simpleton's world of plugging in something and expecting it to work perfectly. What a simple adjustment to have to make for an inexpensive improvement. By the way, the AR-15/M-16 series weapons are much like the M1911/A1 pistols. Gap and space are normal between upper and lower receivers and work perfectly well as designed. This $5.00 part can take that irritating (but harmless) play out without any harmful modification and makes a best-of-both worlds pleaser, that even an idiot without tools can install/de-install. I highly recommend it. I had one in my government issue M-4 while deployed to Iraq in 04-05 where it functioned flawlessly and with much use. When I returned home, I simply took it out and threw it away. Buy one, trim it if you must, use it, you'll love it.

Good product at a good price (23/09/2010)

I custom built my AR with a DS lower and generic upper I bought at a gun show, there was some standard play in between each so I tried out this product. It is easy to install, and solved the problem. I can see how some reciever combos might not work with this wedge, but all you need to do is razor blade some slack off, welcome to the world of gunsmithing.

accu wedge (04/01/2011)

the accu wedge dropped in to my DPMS perfect with no mods, nice and snug now no slop at all

IT DOES MAKE A DIF. (07/08/2011)

M-2- MIKE . IT DOES CHANGE THE SPOT UR SCOPES ON.PLAY BETWEEN UPPER AND LOWER. PUT A BORE SIGHT ON UR AR THEN MOVE THE PLAY SEE WHAT HAPPINS.THIS LITTLE BABY STOPS THAT CHANGE THAT CAN HAPPIN WITH TOO MUCH PLAY.LONG RANGE 1/8 CAN TURN INTO INCHES.IM GETTING 2 MORE.LOL

Installed in a Colt LE carbine (25/08/2011)

Fit perfect, installed in a new rifle but I have others that have loosened up and these always work! No trimming needed for me and it dropped rigfht in!

Perfect fit in my Bushmaster (24/01/2012)

My Bushmaster wasn't very loose to start with, but I figured for [$], why not try it. Dropped right in and fit perfect. Upper is now rock solid and rattle free.

Save your money (01/03/2012)

Wouldn't fit my DPMS without trimming. No difference in tightness between upper and lower.

Works Well As A Buffer.. (03/04/2014)

The polymer Accu-Wedge does not tighten receivers "rock solid" as some proclaim. The receivers will twist side to side according to pin fitment. What the Accu-Wedge does is act as a shock absorber or buffer. Without it the parts slam into each other and wear faster.
I've used many receiver combinations and the wedge has always fit although sometimes closing the receivers requires a good grip. Excess force should not be applied to the upper receiver overhang for the charge handle. The wedge will eventually settle in making closing the receivers easier.
The Accu-Wedge is recommended however I use other means to tighten receivers "rock solid."

Lots of trimming for Rock River lower (15/08/2014)

So this will require a lot of trimming in order to fit a RR lower. I shaved the bottom plug by 75% of its original height, I also had to chop the lip a little as well. Now that's not too big a deal because the play between my Yankee Hill upper and the lower is 99% gone, 100% no rattle. Just be sure to use a nice, small box cutter.. I used my Cold Steel XL Espada.. that was tricky.

Not for M&P 15 (08/02/2017)

Not enough room under or in back of the TDP on a S&W M&P 15. Trimming this thing was a chore, like trying to hold a piece of jello and tough to get a smooth cut. Had the base down to about 1/8" thick and about 1/8" off the wedge and still couldn't get the rifle closed enough to pin it. While I might recommend this to someone based on its good concept, it just doesn't work with this particular model AR.

Works great (28/07/2017)

My Colt SBR lower had a lot of slop in it. To much.....

I purchased one of these, trimmed it to fit and not it doesn't rattle anymore.

P.S. Slop between lower and upper has nothing to do with accuracy. Only shooter confidence.

For me it was annoying to have that much slop.

I WAS annoying.

It took the wibble out of my wobble (26/11/2017)

I just bought a new AR15 and the upper to lower fit was not satisfactory. However because it did not pose a safety problem I looked to Brownell's for the fix and found it when a friend recommended the AccuWedge. I installed it and found it needed a bit of trimming to allow the halves to fit. Dremel to the rescue. 1 minute's work and the wedge fit perfectly. No more wobble and loose fit. Thanks Brownell's.

Get a razorblade ready (02/02/2018)

First, understand that Browne!ls is great with which to do business; I use them a lot. But not all products they sell have that stellar reputation.

I installed the wedge on a S&W M&P 15 TS, and maybe tolerances are tighter. But I ended up cutting away about 60% of it before I could get the pin to lock the upper. Instructions say "squeeze" the upper down to lock. More like use a vise, which I certainly wasn't going to do. So I went to whittling.

Does it stop wobble? Yes.

Is it worth the price? Maybe not, especially if you have to whittle it down to almost nothing.

Got a loose fit on your AR? Might help.

Will I buy another? Probably not. For many years I didn't use one, and never missed it.

If the round base were MUCH thinner it would probably be a drop in.

Maybe buy a couple of school erasers for 50 cents and make your own.

I give it 3 stars.

Leggi più recensioni su brownells.com

14.6 14.6 1 EUR

Sale

N. prodotto: 993150100
Z-M WEAPONS ACCU-WEDGE
Parti Fabbricante: AW400 Aiuta a promuove la migliore precisione rendendo il ricevitore superiore e inferiore in forma più rigorosa. Ricevitore superiore aperto; rilasciare questa lunga durata, il cuneo di gomma nella parte posteriore inferiore, dietro il perno di Spinta. Assolutamente nessuna modifica necessaria.

12.4 EUR 610 12,40 € * 14,60 €

+10 disponibili presso il magazzino Brownells USA

Caratteristiche: Adatto per: AR-15

Aggiungi alla lista degli acquisti

Domande

Dettagli

Aggiungi alla lista degli acquisti

Domande

Caratteristiche

Adatto per: AR-15 Peso della spedizione: 0,005kg Larghezza: 57mm Lunghezza: 89mm

Dettagli dell'elemento

Made in Usa

Instantly Tightens Loose Upper & Lower Receivers

SPECS: High-density, thermo-plastic rubber, ½" (12.5mm) long.

Altro...

Stringe immediatamente sciolti ricevitori superiore & inferiore

Specifiche: in gomma ad alta densità, termo-plastica, ½"(12.5 mm) lungh.

Altro...

Punteggi dei clienti per Z-M WEAPONS ACCU-WEDGE

Numero di punteggi: 17
Da brownells.com: 17
Punteggio medio: 4

Really tightens things up! (14/09/2009)

No brainer-- get it!!! (31/10/2009)

DOES NOT WORK WITH RRA and S&W AR15 (19/12/2009)

Accu Wedge will not work on RRA ARs (06/02/2010)

Accu-Wedge (22/05/2010)

Good product at a good price (23/09/2010)

accu wedge (04/01/2011)

the accu wedge dropped in to my DPMS perfect with no mods, nice and snug now no slop at all

IT DOES MAKE A DIF. (07/08/2011)

Installed in a Colt LE carbine (25/08/2011)

Fit perfect, installed in a new rifle but I have others that have loosened up and these always work! No trimming needed for me and it dropped rigfht in!

Perfect fit in my Bushmaster (24/01/2012)

My Bushmaster wasn't very loose to start with, but I figured for [$], why not try it. Dropped right in and fit perfect. Upper is now rock solid and rattle free.

Save your money (01/03/2012)

Wouldn't fit my DPMS without trimming. No difference in tightness between upper and lower.

Works Well As A Buffer.. (03/04/2014)

Lots of trimming for Rock River lower (15/08/2014)

Not for M&P 15 (08/02/2017)

Works great (28/07/2017)

It took the wibble out of my wobble (26/11/2017)

Get a razorblade ready (02/02/2018)

Leggi più recensioni su brownells.com

Scelti da altri clientie
In alternativa

Sale

BROWNELLS ACCU-WEDGE
AR-15/M16 ACCU-WEDGE

BROWNELLS

Acquista in backorder da magazzino Brownells USA - Il prodotto verrà spedito quando sarà nuovamente disponibile Acquista in backorder da magazzino Brownells USA - Il prodotto verrà spedito quando sarà nuovamente disponibile

10,50 € *

Prezzo al pubblico 12,30 €

Riduttore di gioco

4 (26)

Sale

MAGPUL B.A.D. LEVER
AR-15/M16 B.A.D. LEVER™

MAGPUL

+10 disponibili presso il magazzino Brownells USA +10 disponibili presso il magazzino Brownells USA

39,60 € *

Prezzo al pubblico 46,60 €

0 (0)

A-ZOOM 7MM-08 REMINGTON SNAP CAPS 2/PACK
AMMO SNAP CAP DUMMY ROUNDS

A-ZOOM

Disponibile 2 disponibili presso il magazzino Brownells USA

30,20 € * 21,70 € - 62,50 €*

Salvapercussori

4,2 (35)

Sale

ROCK RIVER ARMS M4 STOCK WRENCH
AR-15 M4 STOCK WRENCH

ROCK RIVER ARMS

+10 disponibili presso il magazzino Brownells USA +10 disponibili presso il magazzino Brownells USA

17,70 € *

Prezzo al pubblico 20,80 €

Chiavi

3,7 (51)

BROWNELLS AR-15/M16 CHAMBER BRUSH 8-36M THREADS
M16 & AR-15 CHAMBER BRUSHES

BROWNELLS

Disponibile +10 disponibili presso il magazzino Brownells USA

19,10 € * 13,60 € - 19,10 €*

Scovoli per camere

4,8 (6)

Sale

COLT ACCU-WEDGE
ACCU-WEDGE

COLT

+10 disponibili presso il magazzino Brownells USA +10 disponibili presso il magazzino Brownells USA

18,90 € *

Prezzo al pubblico 22,20 €

Riduttore di gioco

0 (0)

Sale

BROWNELLS ACCU-WEDGE
AR-15/M16 ACCU-WEDGE

BROWNELLS

10,50 € *

Prezzo al pubblico 12,30 €

Riduttore di gioco

4 (26)

Accesso

Hai dimenticato la password?
Registrati

Social Media

Brownells.it

Catalogo prodotti

Ordinare

Customer Service

Benvenuti!

Benvenuti su Brownells.it, il principale rivenditore online di accessori per armi da fuoco, componenti di pistole e utensili per armaioli in Italia!

La nostra offerta

Se ti piace sparare, lavorare sulle armi da fuoco come artigiano o per hobby, o semplicemente possiedi un'arma, questo è il posto per te!

Grazie alla nostra grande esperienza, ogni giorno, tiratori, armaioli professionisti, hobbisti, militari, esponenti delle forze dell'ordine e appassionati d'armi si rivolgono a Brownells.it per trovare accessori e componenti di alta qualità e fare rifornimento di ciò di cui hanno bisogno.

Nel nostro negozio online potrai trovare oltre 60.000 prodotti, tra cui parti d'arma, accessori, utensili per armieri, materiale per ricarica e componenti di munizioni, e altri prodotti per mantenere, riparare e aggiornare le tue armi.