Recuts Lug For A Tight Fitting Barrel That Improves Accuracy
Hand operated, carbide cutter easily trims excess material from the bottom barrel lug when fitting custom or factory barrels to 1911 Autos. Cuts barrel lugs parallel, and with the correct height and radius, to help produce the best possible lockup. Use .186" cutter first, then progress to the .195" cutter if more material needs to be removed. Follow with careful hand fitting to achieve a firm, non-binding barrel-to-slide fit. Start small and check your work often. It is possible, with some slide/barrel combinations, that the .195" cutter could remove more material than necessary. Fits all 1911 Auto, Commander and Officers ACP, single- and double-stack frames.
SPECS: 1" (2.5cm) diameter knob; 2.07" (5.25cm) long shank. .186" (4.72mm) or .195" (4.95mm) diameter cutters. Complete instructions included.
Altro...
Recuts Lug per un barile di aderente che migliora la precisione
Azionato a mano, Fresa carburo elimina facilmente il materiale in eccesso dalla linguetta di canna inferiore durante il montaggio personalizzato o botti di fabbrica al 1911 Autos. Tagli in botte alette parallele e con la giusta altezza e raggio, per contribuire a produrre i migliore possibili guardina. Uso. 186" fresa prima, poi il progresso per i. 195" fresa se più materiale deve essere rimosso. Seguire con attenzione mano propizia per ottenere una misura di canna-a-faccia scorrere ditta, non vincolante. Inizio piccole e controllare spesso il lavoro. È possibile, con alcune combinazioni di diapositiva alla canna, che i. 195" fresa potrebbe rimuovere più materiale del necessario. Si adatta a tutte le Auto del 1911, ACP comandante e ufficiali, single e double-stack frame.
Specifiche: 1"(2,5 cm) manopola diametro; 2,07 (cm 5.25) lunga tibia.. 186" (4.72 mm) o. 195"(4.95 mm) frese di diametro. Completare le istruzioni incluse.
Altro...
Punteggi dei clienti per BROWNELLS 1911 LUG CUTTER HANDLE W/0.195" CUTTER
Numero di punteggi: 4
Da brownells.com: 4
Punteggio medio: 2,8
Do not buy!!(14/11/2013)
The new cutters are brittle and will break one first time use.
A must tool for gunsmiths(20/12/2011)
This lug cutter is easy to use and does a professional job.
Change In Design (09/10/2014)
The design of the .186 cutter was changed to a helix design. I cut 3 lower lugs on barrels and the teeth sheared off in one area on the third barrel. The old "burr" style cutter must have fit 30-40 barrels before it broke. Please bring back the old style. Helix is fine for the .195 cutter as it delivers a smoother cut.
Works well(25/01/2015)
I've had this lug cutter for a few years and it has worked well for me. It should be used with the handle on the left side of the frame as viewed from the rear other wise the cutter will grab the barrel lug pulling it forward and braking the cutter. Clean and oil it often and it will cut cleanly. It would be nice if the support bushing was attached to the cutter, I also had to turn a shoulder on the bushing in order for it to clear the slide and have full engagement in the frame, although it did work the way it was.
N. prodotto: 080000068 BROWNELLS 1911 LUG CUTTER HANDLE W/0.195" CUTTER Azionato a mano, Fresa carburo elimina facilmente il materiale in eccesso dalla linguetta di canna inferiore durante il montaggio personalizzato o botti di fabbrica al 1911 Autos. Tagli in botte alette parallele e con la giusta altezza e raggio, per contribuire a produrre i migliore possibili guardina. Uso. 186" fresa prima, poi il progresso per i. 195" fresa se più materiale deve essere rimosso. Seguire con attenzione mano propizia per ottenere una misura di canna-a-faccia scorrere ditta, non vincolante. Inizio piccole e controllare spesso il lavoro. È possibile, con alcune combinazioni di diapositiva alla canna, che i. 195" fresa potrebbe rimuovere più materiale del necessario. Si adatta a tutte le Auto del 1911, ACP comandante e ufficiali, single e double-stack frame.
129.9EUR50129,90 €
*
Tempi di consegna circa 12-16 giorni. Più di 10 pz. nel magazzino USA
N. prodotto: 080000067 BROWNELLS 1911 LUG CUTTER HANDLE W/0.186" CUTTER Azionato a mano, Fresa carburo elimina facilmente il materiale in eccesso dalla linguetta di canna inferiore durante il montaggio personalizzato o botti di fabbrica al 1911 Autos. Tagli in botte alette parallele e con la giusta altezza e raggio, per contribuire a produrre i migliore possibili guardina. Uso. 186" fresa prima, poi il progresso per i. 195" fresa se più materiale deve essere rimosso. Seguire con attenzione mano propizia per ottenere una misura di canna-a-faccia scorrere ditta, non vincolante. Inizio piccole e controllare spesso il lavoro. È possibile, con alcune combinazioni di diapositiva alla canna, che i. 195" fresa potrebbe rimuovere più materiale del necessario. Si adatta a tutte le Auto del 1911, ACP comandante e ufficiali, single e double-stack frame.
129.9EUR12129,90 €
*
Tempi di consegna circa 12-16 giorni. Più di 10 pz. nel magazzino USA
Recuts Lug For A Tight Fitting Barrel That Improves Accuracy
Hand operated, carbide cutter easily trims excess material from the bottom barrel lug when fitting custom or factory barrels to 1911 Autos. Cuts barrel lugs parallel, and with the correct height and radius, to help produce the best possible lockup. Use .186" cutter first, then progress to the .195" cutter if more material needs to be removed. Follow with careful hand fitting to achieve a firm, non-binding barrel-to-slide fit. Start small and check your work often. It is possible, with some slide/barrel combinations, that the .195" cutter could remove more material than necessary. Fits all 1911 Auto, Commander and Officers ACP, single- and double-stack frames.
SPECS: 1" (2.5cm) diameter knob; 2.07" (5.25cm) long shank. .186" (4.72mm) or .195" (4.95mm) diameter cutters. Complete instructions included.
Altro...
Recuts Lug per un barile di aderente che migliora la precisione
Azionato a mano, Fresa carburo elimina facilmente il materiale in eccesso dalla linguetta di canna inferiore durante il montaggio personalizzato o botti di fabbrica al 1911 Autos. Tagli in botte alette parallele e con la giusta altezza e raggio, per contribuire a produrre i migliore possibili guardina. Uso. 186" fresa prima, poi il progresso per i. 195" fresa se più materiale deve essere rimosso. Seguire con attenzione mano propizia per ottenere una misura di canna-a-faccia scorrere ditta, non vincolante. Inizio piccole e controllare spesso il lavoro. È possibile, con alcune combinazioni di diapositiva alla canna, che i. 195" fresa potrebbe rimuovere più materiale del necessario. Si adatta a tutte le Auto del 1911, ACP comandante e ufficiali, single e double-stack frame.
Specifiche: 1"(2,5 cm) manopola diametro; 2,07 (cm 5.25) lunga tibia.. 186" (4.72 mm) o. 195"(4.95 mm) frese di diametro. Completare le istruzioni incluse.
Altro...
Punteggi dei clienti per BROWNELLS 1911 LUG CUTTER HANDLE W/0.195" CUTTER
Numero di punteggi: 4
Da brownells.com: 4
Punteggio medio: 2,8
Do not buy!!(14/11/2013)
The new cutters are brittle and will break one first time use.
A must tool for gunsmiths(20/12/2011)
This lug cutter is easy to use and does a professional job.
Change In Design (09/10/2014)
The design of the .186 cutter was changed to a helix design. I cut 3 lower lugs on barrels and the teeth sheared off in one area on the third barrel. The old "burr" style cutter must have fit 30-40 barrels before it broke. Please bring back the old style. Helix is fine for the .195 cutter as it delivers a smoother cut.
Works well(25/01/2015)
I've had this lug cutter for a few years and it has worked well for me. It should be used with the handle on the left side of the frame as viewed from the rear other wise the cutter will grab the barrel lug pulling it forward and braking the cutter. Clean and oil it often and it will cut cleanly. It would be nice if the support bushing was attached to the cutter, I also had to turn a shoulder on the bushing in order for it to clear the slide and have full engagement in the frame, although it did work the way it was.