Rimuove le ammaccature dalle costolature di ventilazione dei fucili a canna liscia in pochi minuti. Facile da attaccare e veloce nell'utilizzo. Il ponte in ottone non lascia segni sulla parte superiore della costolatura; le mascelle in acciaio si auto-regolano.
SPECIFICHE: Ponte; in ottone lavorato, lungo 3" (7,6 cm) e spesso ¼" (6,3 mm). Mascella; in acciaio lavorato e indurito, lunga 1½" (3,8 cm) e larga al punto più ampio ½" (12,7 mm).
Altro...
Punteggi dei clienti per MURRAYS VENT RIB TOOL
Numero di punteggi: 5
Da brownells.com: 5
Punteggio medio: 5
Cheaper than a new rib!(09/03/2010)
I used this tool to remove two severe dents in the rib of my Ruger O/U. I was very tentative at first, but once I got used to the pressure it worked like a charm. You do have to slightly over tighten to ensure the dent is removed. A heavy hand could convert a dent to a hump. Patience and checking with a steel rule will keep you in a great place.
Handy little tool(10/07/2012)
Neatest thing since a pocket on a shirt. Pulls dinged ribs right up. Like the other reviewer noted, you do need to pull it up a little higher than flat and check it with a flat edge, but works like it's supposed to.
works graet, easy to use (01/12/2014)
I have used this tool about 10 times and it has worked great, easy and fast, One great tool.
Better than a gunsmith (13/06/2015)
Simple to use tool that works! I used this on my baby a Perazzi, did not want to ship the gun off. Prior dent is not noticeable after a bit of cold blue touch up. Use with caution, adjust, measure and repeat.
Christmas surprise (26/12/2016)
Unsightly crimp in my over under vent rib near the mid sight. Took it to three gunsmiths. Two refused to fix it and one wanted $150 and to remove my mid sight mark. I said no and lived with the crimp for a year. Then this Christmas my wife ordered the Murray vent rib tool from Brownells.. Was just going to test the fit of the tool and realized I could fix it. Took me seconds and my barrell was good as new. Every shotgunner with vent ribs needs this tool.
N. prodotto: 563100000 MURRAYS VENT RIB TOOL Parti Fabbricante: NONE Rimuove le ammaccature dalle costolature di ventilazione dei fucili a canna liscia in pochi minuti. Facile da attaccare e veloce nell'utilizzo. Il ponte in ottone non lascia segni sulla parte superiore della costolatura; le mascelle in acciaio si auto-regolano.
109.9EUR34109,90 €
*
Tempi di consegna circa 12-16 giorni. Più di 10 pz. nel magazzino USA
Rimuove le ammaccature dalle costolature di ventilazione dei fucili a canna liscia in pochi minuti. Facile da attaccare e veloce nell'utilizzo. Il ponte in ottone non lascia segni sulla parte superiore della costolatura; le mascelle in acciaio si auto-regolano.
SPECIFICHE: Ponte; in ottone lavorato, lungo 3" (7,6 cm) e spesso ¼" (6,3 mm). Mascella; in acciaio lavorato e indurito, lunga 1½" (3,8 cm) e larga al punto più ampio ½" (12,7 mm).
Altro...
Punteggi dei clienti per MURRAYS VENT RIB TOOL
Numero di punteggi: 5
Da brownells.com: 5
Punteggio medio: 5
Cheaper than a new rib!(09/03/2010)
I used this tool to remove two severe dents in the rib of my Ruger O/U. I was very tentative at first, but once I got used to the pressure it worked like a charm. You do have to slightly over tighten to ensure the dent is removed. A heavy hand could convert a dent to a hump. Patience and checking with a steel rule will keep you in a great place.
Handy little tool(10/07/2012)
Neatest thing since a pocket on a shirt. Pulls dinged ribs right up. Like the other reviewer noted, you do need to pull it up a little higher than flat and check it with a flat edge, but works like it's supposed to.
works graet, easy to use (01/12/2014)
I have used this tool about 10 times and it has worked great, easy and fast, One great tool.
Better than a gunsmith (13/06/2015)
Simple to use tool that works! I used this on my baby a Perazzi, did not want to ship the gun off. Prior dent is not noticeable after a bit of cold blue touch up. Use with caution, adjust, measure and repeat.
Christmas surprise (26/12/2016)
Unsightly crimp in my over under vent rib near the mid sight. Took it to three gunsmiths. Two refused to fix it and one wanted $150 and to remove my mid sight mark. I said no and lived with the crimp for a year. Then this Christmas my wife ordered the Murray vent rib tool from Brownells.. Was just going to test the fit of the tool and realized I could fix it. Took me seconds and my barrell was good as new. Every shotgunner with vent ribs needs this tool.