Il Carrello è vuoto.

Carrello

0364 1955 195

Iscriviti alla Newsletter

XS SIGHT SYSTEMS
STANDARD DOT TRITIUM SIGHTS FOR RUGER®

647533038317 006000171

Replacement front sights have a high-visibility white outline surrounding a Tritium insert for easy sight acquisition in all types of ambient light—from bright sunlight to nighttime, and anything in between. Low, streamlined, no-snag shape makes these sights excellent for concealed carry guns. Model available for Ruger® LCR®.

SPECS: Machined steel, matte black finish. LCR - .110" (2.8mm) dia. dot. Gunsmith installation recommended.

Altro...

Le mire anteriori di ricambio hanno un contorno bianco ad alta visibilità che circonda un inserto Tritium per facilitare l'acquisizione del bersaglio in tutti i tipi di luce ambientale - dalla luce solare intensa alla notte, e tutto ciò che si trova in mezzo. La forma bassa e aerodinamica, senza sporgenze, rende queste mire eccellenti per le armi da porto occulto. Modello disponibile per Ruger® LCR®.

SPECIFICHE: Acciaio lavorato, finitura opaca nera. LCR - diametro del punto .110" (2,8mm). Si consiglia l'installazione da parte di un armaiolo.

Altro...

Punteggi dei clienti per XS SIGHT SYSTEMS STANDARD DOT TRITIUM SIGHTS-RUGER LCR .38/.357 ONLY

Numero di punteggi: 5
Da brownells.com: 5
Punteggio medio: 4,6

JUST WHAT YOUR CARRY WEAPON WANTS (30/12/2011)

EXCELLENT SIGHTS,CAN BE INSTALLED WITH THE RIGHT TOOLS AND SOME PATIENCE.VERY GOOD DIRECTIONS ON INSTALL.LOW LIGHT OR NO LIGHT VISIBILITY. JUST WHAT ANY CARRY OR PERSONEL PROTECTION WEAPON SHOULD HAVE. A+++++++++++

Excellent Replacement Sight for LCR (08/04/2012)

I purchased a LCR for my wife as a CCW, and I was not really satisfied with the stock sight. It was decent enough, but I think for CCW low light performance is a must. So after some reading I decided on this one.

The package comes with: 1) The Sight, 2) a new roll pin, 3) a punch, and 4) a small tube of blue loctite.

Installation took a total of 20 minutes, and I am far from a "handy man". I won't go into the details of the installation, because the supplied instructions are very detailed (including pictures). I would give 2 pieces of advice for those of you that aren't gunsmiths and don't have all the fancy tools.

1) Get a roll of masking tape to hold the gun in place while you punch out / replace the roll pin. The cylinder sits perfectly inside the roll, it holds steady, and won't hurt the guns finish at all.

2) Get a real, GOOD punch. The one supplied works well enough for removing the stock roll pin, but was a terrible pain to replace the new pin. I knocked the old pin out with 2 hits, but the pin was bent in the process (yes after 2 hits). I was able to get the new pin started with the bent pin, but could not finish driving it. I got a larger sized punch to cover the whole head of the pin; 1 smack and the sight was ready to roll.

Lastly, this sight is not lined up like a standard revolver sight. Originally, you put the tip of the post under what you wanted to hit. With this, you put the center of the "dot" on top of your target. This is excellent for CCW and man sized targets. However, if you are using this a range queen, hitting steel plates at a distance takes some getting used to.

*Note* - I will assume all guns are different, but this is my experience with the sight. XS says to lay the white of the dot down inside the rear sight notches. This was not the true (in my case). I actually have to put the white of the dot on the top of the rear sight notches. Just something to consider if you buy it and can't seem to hit anything (I know I couldn't! haha).

All in all, I am very pleased with this sight, and yes I would purchase it again.

Then there was Light!!!!!!! (16/08/2012)

Easy to install, took me about 20 minutes. (Zero gunsmithing abilities at all)

Comes with a punch but it eventually broke (can't complain too much about that because most items you buy don't come with tools!)

Looks great, sight picture is much better (have not fired yet)

Glows nicely in pitch black room.

I tried to use roll pin from LCR I took out but it ended up mushrooming so I used the supplied one and it fit and works fine.

Highly recommend this to any LCR owners!

Nothing like quick service (01/04/2013)

I ordered this last Friday after lunch and it arrived today.(Monday)

I installed it this evening. No problems. I read where the punch is getting bent. I always use a lot of light taps to remove this type of pin. After removing the old pin, the supplied punch looks like it came out of the package.

I do recommend that you start the pin in the sight just enough to hold it but not enough to keep it from seating on the top of the LCR. This makes it easier to finish the install. I also recommend that you use a hammer with an alluminum head as this will not damage the pin or your LCR.

When I installed the pin, I used the fat end of the supplied punch to seat it, again using several taps that are not hard enough to bend the punch.

I hope that this helps others to avoid problems that others had.

sight is good but no extra pin (17/07/2015)

Leggi più recensioni su brownells.com

129.9 129.9 1 EUR

N. prodotto: 006000171
XS SIGHT SYSTEMS STANDARD DOT TRITIUM SIGHTS-RUGER LCR .38/.357 ONLY
Parti Fabbricante: RP-0008N-4 647533038317 Le mire anteriori di ricambio hanno un contorno bianco ad alta visibilità che circonda un inserto Tritium per facilitare l'acquisizione del bersaglio in tutti i tipi di luce ambientale - dalla luce solare intensa alla notte, e tutto ciò che si trova in mezzo. La forma bassa e aerodinamica, senza sporgenze, rende queste mire eccellenti per le armi da porto occulto. Modello disponibile per Ruger® LCR®.

129.9 EUR 3 129,90 € *

Tempi di consegna circa 12-16 giorni.
3 pz. nel magazzino USA

Caratteristiche: Adatto per: Ruger Modello: LCR Tipo: Dot, Low-Profile, Mira notturna

Aggiungi alla lista degli acquisti

Domande

Dettagli

Aggiungi alla lista degli acquisti

Domande

Caratteristiche

Adatto per: Ruger Modello: LCR Tipo: Dot,Low-Profile,Mira notturna Peso della spedizione: 0,068kg Altezza di spedizione: 41mm Larghezza di spedizione: 122mm Lunghezza di spedizione: 198mm

Dettagli dell'elemento

Made in Usa

SPECS: Machined steel, matte black finish. LCR - .110" (2.8mm) dia. dot. Gunsmith installation recommended.

Altro...

SPECIFICHE: Acciaio lavorato, finitura opaca nera. LCR - diametro del punto .110" (2,8mm). Si consiglia l'installazione da parte di un armaiolo.

Altro...

Punteggi dei clienti per XS SIGHT SYSTEMS STANDARD DOT TRITIUM SIGHTS-RUGER LCR .38/.357 ONLY

Numero di punteggi: 5
Da brownells.com: 5
Punteggio medio: 4,6

JUST WHAT YOUR CARRY WEAPON WANTS (30/12/2011)

Excellent Replacement Sight for LCR (08/04/2012)

Then there was Light!!!!!!! (16/08/2012)

Nothing like quick service (01/04/2013)

sight is good but no extra pin (17/07/2015)

Leggi più recensioni su brownells.com

Accesso

Hai dimenticato la password?
Registrati

Social Media

Brownells.it

Catalogo prodotti

Ordinare

Customer Service

Benvenuti!

Benvenuti su Brownells.it, il principale rivenditore online di accessori per armi da fuoco, componenti di pistole e utensili per armaioli in Italia!

La nostra offerta

Se ti piace sparare, lavorare sulle armi da fuoco come artigiano o per hobby, o semplicemente possiedi un'arma, questo è il posto per te!

Grazie alla nostra grande esperienza, ogni giorno, tiratori, armaioli professionisti, hobbisti, militari, esponenti delle forze dell'ordine e appassionati d'armi si rivolgono a Brownells.it per trovare accessori e componenti di alta qualità e fare rifornimento di ciò di cui hanno bisogno.

Nel nostro negozio online potrai trovare oltre 60.000 prodotti, tra cui parti d'arma, accessori, utensili per armieri, materiale per ricarica e componenti di munizioni, e altri prodotti per mantenere, riparare e aggiornare le tue armi.