Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.811" Overall Width: .99" Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter. FITS: Sig P210 Target (American Only Post 2016) EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation.
Mount per il tuo red dot SIG SAUER P210A TARGET
Scopri il montaggio per il tuo red dot Vortex Viper/Venom progettato specificamente per la pistola Sig P210 Target. Questo prodotto è realizzato con materiali di alta qualità per garantire prestazioni superiori.
Descrizione del prodotto
- Materiale: Alluminio 7075
- Rivestimento: Nero opaco Hardcoat
- Dimensioni: Lunghezza totale: 1.811", Larghezza totale: .99"
- Hardware di montaggio:
- (2) Viti a testa a bottone 6-32
- (2) Viti a testa piatta 6-32
- (1) Vite di bloccaggio 6-32
- Compatibilità: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter
- FITS: Sig P210 Target (solo americano post 2016)
Le mire red dot di EGW sono progettate per essere installate da sinistra a destra (con la bocca della canna rivolta in avanti). La slitta ha una inclinazione progressiva per facilitare l'installazione. Rimuovi semplicemente la mira posteriore della tua pistola e sostituiscila con il nostro montaggio per installare il tuo red dot Vortex Viper/Venom, Burris FastFire o Docter. Non sono necessarie modifiche. Puoi rimuovere il nostro montaggio e sostituire la mira posteriore in qualsiasi momento. Hardware di montaggio incluso.
Istruzioni di installazione
- Rimuovi la mira posteriore
- Installa il montaggio EGW nella slitta
- Serra la vite di bloccaggio (se applicabile)
- Posiziona il red dot sul montaggio EGW (mettere un piccolo pezzo di carta tra il red dot e il montaggio faciliterà la rimozione e terrà il Loctite lontano dal red dot).
- Applica Loctite blu alle viti di montaggio fornite
- Serra le viti di montaggio a 15in/lbs
Le viti incluse con questo montaggio richiedono una chiave a brugola da 5/64'' per l'installazione.