Brownells Italia - Il negozio online del più grande rivenditore di componenti e accessori per armi da tiro, difesa e caccia Italia

EGW
H&K VP9, P30, HK45, VP40 LEUPOLD DELTAPOINT PRO SIGHT MOUNT

841370114221 296000683
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount is not intended for use with the optics ready version of these pistols. This mount does not fit: HK USP
0 0 1 EUR
N. prodotto: 296000683
EGW H&K VP9, P30, HK45, VP40 LEUPOLD DELTAPOINT PRO SIGHT MNT
Parti Fabbricante: 49408 841370114221 Le mire a punto rosso EGW sono progettate per essere installate da sinistra a destra (con la volata rivolta in avanti). La coda di rondine ha una conicità progressiva per facilitare l'installazione. Rimuovere semplicemente la mira posteriore dalla vostra arma e sostituirla con il supporto EGW per montare il vostro Leupold DeltaPoint Pro, JPoint, Redfield Accelerator o Optima red-dot sight. È possibile rimuovere il supporto e ripristinare la mira posteriore in qualsiasi momento. Hardware di montaggio incluso. Istruzioni di installazione Rimuovere la mira posteriore* Installare il supporto EGW nella coda di rondine Stringere la vite di fissaggio (se applicabile) Posizionare il mirino a punto rosso sul supporto EGW (mettere un piccolo pezzo di carta tra il mirino a punto rosso e il supporto mirino faciliterà la rimozione e terrà il Loctite lontano dal mirino a punto rosso.) Applicare il Loctite blu alle viti di montaggio fornite Serrare le viti di montaggio a 15in/lbs La modifica della vostra arma da fuoco può annullare la garanzia del produttore. Questo prodotto dovrebbe essere installato e controllato da un armaiolo qualificato. Non si esprime o si implica alcuna responsabilità per danni o lesioni che possono risultare da un'installazione o uso improprio di questo prodotto. Questo supporto non è destinato all'uso con la versione delle pistole pronte per ottiche. Questo supporto non è compatibile con: HK USP
Avvisa quando diventa disponibile
Non disponibile.
Caratteristiche: Adatto per: Heckler & Koch Colore: Nero Materiale: Alluminio Modello: P30, 45, VP9, P30L, 45C, VP40, VP9SK, P30sk Numero di basi: 1 pezzo Tipo: Tattico

Caratteristiche

Adatto per: Heckler & Koch Colore: Nero Materiale: Alluminio Modello: P30L,45,P30,45C,VP9SK,VP9,VP40,P30sk Numero di basi: 1 pezzo Tipo: Tattico Peso della spedizione: 0,045kg Altezza di spedizione: 25mm Larghezza di spedizione: 76mm Lunghezza di spedizione: 140mm

Dettagli dell'elemento

Made in Usa



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount is not intended for use with the optics ready version of these pistols. This mount does not fit: HK USP
Newsletter