Brownells Italia - Il negozio online del più grande rivenditore di componenti e accessori per armi da tiro, difesa e caccia Italia

EGW
WALTHER 22 LEUPOLD DELTAPOINT PRO SIGHT MOUNT

841370115679 296000679
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mountwill make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Colt 1911/.22 Rail Gun (Walther .22 Slide) This mount fits the Colt Rail Gun .22lr that has the slide made by Walther.
0 0 1 EUR
N. prodotto: 296000679
EGW WALTHER 22 LEUPOLD DELTAPOINT PRO SIGHT MOUNT
Parti Fabbricante: 49404 841370115679 Le mire a punto rosso EGW sono progettate per essere installate da sinistra a destra (con la volata rivolta in avanti). La coda di rondine ha una conicità progressiva per permettere un'installazione più facile. Semplicemente rimuovi la mira posteriore dalla tua arma e sostituiscila con il supporto EGW per montare il tuo Leupold DeltaPoint Pro, JPoint, Redfield Accelerator o mira a punto rosso Optima. Puoi rimuovere il supporto e sostituire la mira posteriore in qualsiasi momento. Hardware di montaggio incluso. Istruzioni per l'installazione Rimuovere la mira posteriore* Installare il Supporto Mira EGW nella coda di rondine Stringere la vite di fissaggio (se applicabile) Posizionare la mira a punto rosso sul Supporto Mira EGW (mettere un piccolo pezzo di carta tra la mira a punto rosso e il supporto mira renderà la rimozione più facile e terrà il Loctite lontano dalla mira a punto rosso.) Applicare Loctite blu alle viti di montaggio fornite Stringere le viti di montaggio a 15in/lbs La modifica della tua arma da fuoco può annullare la garanzia del produttore. Questo prodotto dovrebbe essere installato e controllato da un armaiolo qualificato. Non si assume alcuna responsabilità per danni o lesioni che possono derivare dall'installazione o dall'uso improprio di questo prodotto. Questo supporto si adatta a: Colt 1911/.22 Rail Gun (scorrevole Walther .22) Questo supporto si adatta alla Colt Rail Gun .22lr che ha lo scorrevole realizzato da Walther.
Avvisa quando diventa disponibile
Non disponibile.
Caratteristiche: Adatto per: Walther, Colt Colore: Nero Materiale: Alluminio Modello: P22, 1911 Numero di basi: 1 pezzo Tipo: Tattico

Caratteristiche

Adatto per: Walther,Colt Colore: Nero Materiale: Alluminio Modello: P22,1911 Numero di basi: 1 pezzo Tipo: Tattico Peso della spedizione: 0,045kg Altezza di spedizione: 25mm Larghezza di spedizione: 76mm Lunghezza di spedizione: 140mm

Dettagli dell'elemento

Made in Usa



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mountwill make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Colt 1911/.22 Rail Gun (Walther .22 Slide) This mount fits the Colt Rail Gun .22lr that has the slide made by Walther.
Newsletter