Protects Critical Locking Lugs When Welding Or Forging Bolt Handles
Provides protection to locking lugs when welding or forging bolt handles by pulling heat away from these critical areas and dissipating it. Especially effective when used with Heat Control Paste. Threaded to fit securely into rear of bolt body, giving additional protection to interior threads by preventing scale formation. Flats milled on end allow use of wrench. Available separately or as a Set of five.
SPECS: Steel, blued. 4¼" (10.8cm) to 5½" (14cm) long depending on the model. #1 - 1903 & 03A3 Springfields, #3 - 98 Mauser, #4 - Remington 700.
Altro...
Protegge le alette di bloccaggio critici quando saldatura o forgiatura bullone maniglie
Fornisce protezione alle alette di bloccaggio quando la saldatura o forgiatura bullone maniglie tirando il calore lontano da queste aree critiche e dissipando esso. Particolarmente efficace se usato con pasta di controllo del calore. Filettato per montare saldamente nella parte posteriore del corpo del bullone, dando ulteriore protezione ai thread interni di prevenire la formazione di scala. Appartamenti fresati su fine consentono l'utilizzo della chiave. Disponibili separatamente o come un Set di cinque.
Specifiche: acciaio, brunito. 4¼"(10.8 cm) a 5½" (14 cm) lungo a seconda del modello. #1 - 1903 & 03A3 Springfields, #3 - Mauser 98, #4 - Remington 700, #5 - Winchester M70.
Altro...
Punteggi dei clienti per BROWNELLS #1 BOLT HEAT SINK
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 5
Great Product!(19/09/2015)
Purchased this to silver solder a bolt handle back onto a Remington 600 Mohawk bolt body. Since made for a Rem 700, it was too long. You can either cut off 1/2" of material or turn down
last 1/2" of dowel to under .200" to fit properly. The threads are the same. Worked perfectly according to supplied instructions. Use heat paste!!!
The Obvious Industry Standard(06/09/2009)
I used to use a slightly less expensive heatsink product from another company. After having a scary moment when the wrench head ripped off while removing it from a Yugo 48 bolt I decided to go with this one.
I don't know how else to say it: the quality of the aluminum in this heatsink is much better. While both heatsinks are the same size the Brownell's version is much heavier. The fit and finish are also drastically better.
I do (gasp!) Oxy-Acetylene welding, and in conjunction with heat-stop paste I have never even approached a warm touch on the lugs of a Yugo 48, Turk, or Vz-24 bolt using this heatsink.
You can go with the copy or go with the original. I should have went with the Brownells's heatsink in the first place.
N. prodotto: 080638001 BROWNELLS #1 BOLT HEAT SINK050806102866 Fornisce protezione alle alette di bloccaggio quando la saldatura o forgiatura bullone maniglie tirando il calore lontano da queste aree critiche e dissipando esso. Particolarmente efficace se usato con pasta di controllo del calore. Filettato per montare saldamente nella parte posteriore del corpo del bullone, dando ulteriore protezione ai thread interni di prevenire la formazione di scala. Appartamenti fresati su fine consentono l'utilizzo della chiave. Disponibili separatamente o come un Set di cinque.
29.9EUR029,90 €
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Caratteristiche:Adatto per: SpringfieldModello: Model 1903, 03-A3
Adatto per:
Springfield
Modello:
03-A3,Model 1903
Peso della spedizione: 0,181kgAltezza: 18mmLarghezza: 76mmLunghezza: 178mm
Dettagli dell'elemento
Made in Usa
N. prodotto: 080638004 BROWNELLS #4 BOLT HEAT SINK Fornisce protezione alle alette di bloccaggio quando la saldatura o forgiatura bullone maniglie tirando il calore lontano da queste aree critiche e dissipando esso. Particolarmente efficace se usato con pasta di controllo del calore. Filettato per montare saldamente nella parte posteriore del corpo del bullone, dando ulteriore protezione ai thread interni di prevenire la formazione di scala. Appartamenti fresati su fine consentono l'utilizzo della chiave. Disponibili separatamente o come un Set di cinque.
29.9EUR329,90 €
*
Tempi di consegna circa 14-21 giorni. 3 pz. nel magazzino USA
N. prodotto: 080638003 BROWNELLS #3 BOLT HEAT SINK Fornisce protezione alle alette di bloccaggio quando la saldatura o forgiatura bullone maniglie tirando il calore lontano da queste aree critiche e dissipando esso. Particolarmente efficace se usato con pasta di controllo del calore. Filettato per montare saldamente nella parte posteriore del corpo del bullone, dando ulteriore protezione ai thread interni di prevenire la formazione di scala. Appartamenti fresati su fine consentono l'utilizzo della chiave. Disponibili separatamente o come un Set di cinque.
31.9EUR031,90 €
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
N. prodotto: 080638000 BROWNELLS BOLT HEAT SINK SET Fornisce protezione alle alette di bloccaggio quando la saldatura o forgiatura bullone maniglie tirando il calore lontano da queste aree critiche e dissipando esso. Particolarmente efficace se usato con pasta di controllo del calore. Filettato per montare saldamente nella parte posteriore del corpo del bullone, dando ulteriore protezione ai thread interni di prevenire la formazione di scala. Appartamenti fresati su fine consentono l'utilizzo della chiave. Disponibili separatamente o come un Set di cinque.
Protects Critical Locking Lugs When Welding Or Forging Bolt Handles
Provides protection to locking lugs when welding or forging bolt handles by pulling heat away from these critical areas and dissipating it. Especially effective when used with Heat Control Paste. Threaded to fit securely into rear of bolt body, giving additional protection to interior threads by preventing scale formation. Flats milled on end allow use of wrench. Available separately or as a Set of five.
SPECS: Steel, blued. 4¼" (10.8cm) to 5½" (14cm) long depending on the model. #1 - 1903 & 03A3 Springfields, #3 - 98 Mauser, #4 - Remington 700.
Altro...
Protegge le alette di bloccaggio critici quando saldatura o forgiatura bullone maniglie
Fornisce protezione alle alette di bloccaggio quando la saldatura o forgiatura bullone maniglie tirando il calore lontano da queste aree critiche e dissipando esso. Particolarmente efficace se usato con pasta di controllo del calore. Filettato per montare saldamente nella parte posteriore del corpo del bullone, dando ulteriore protezione ai thread interni di prevenire la formazione di scala. Appartamenti fresati su fine consentono l'utilizzo della chiave. Disponibili separatamente o come un Set di cinque.
Specifiche: acciaio, brunito. 4¼"(10.8 cm) a 5½" (14 cm) lungo a seconda del modello. #1 - 1903 & 03A3 Springfields, #3 - Mauser 98, #4 - Remington 700, #5 - Winchester M70.
Altro...
Punteggi dei clienti per BROWNELLS #1 BOLT HEAT SINK
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 5
Great Product!(19/09/2015)
Purchased this to silver solder a bolt handle back onto a Remington 600 Mohawk bolt body. Since made for a Rem 700, it was too long. You can either cut off 1/2" of material or turn down
last 1/2" of dowel to under .200" to fit properly. The threads are the same. Worked perfectly according to supplied instructions. Use heat paste!!!
The Obvious Industry Standard(06/09/2009)
I used to use a slightly less expensive heatsink product from another company. After having a scary moment when the wrench head ripped off while removing it from a Yugo 48 bolt I decided to go with this one.
I don't know how else to say it: the quality of the aluminum in this heatsink is much better. While both heatsinks are the same size the Brownell's version is much heavier. The fit and finish are also drastically better.
I do (gasp!) Oxy-Acetylene welding, and in conjunction with heat-stop paste I have never even approached a warm touch on the lugs of a Yugo 48, Turk, or Vz-24 bolt using this heatsink.
You can go with the copy or go with the original. I should have went with the Brownells's heatsink in the first place.