BIS, G43X/48 (Backup Iron Sight, G43X/G48) is a collaboration between Ameriglo and FCD. Specifically made for Glock G43X and G48, these sights are based on the superb Ameriglo GL-527 with a front sight height of 0.450", and a rear sight height of 0.554", this sight sets provide lower 1/3 co-witness with the Trijicon RMRcc when used with the OPF-G43X/43, RMRcc on G43X and G48. BIS, G43X/48 consists of the following: Front sight, available with either green Tritium and white outline (no serrations), or serrated front sight, no tritium or white outline. Rear sight, serrated. BIS, G43X/48 is slightly different from GL-527 on which it's based. These FCD particular changes are: Tritium option for the front sight. Front sight back strap angle is steeper (25 degrees on the serrated, non-tritium front sight, 20 degrees on non-serrated, tritium front sight) to mitigate snagging when the pistol is drawn from and out of the holster where it's likely to encounter clothing, and the front sight's top corners are softened. Rear sight is horizontally serrated. Designed and made in the USA. Special thanks to the professionals at Ameriglo https://ameriglo.com/ that made this project possible, Forward Controls Design are grateful for their willingness to work with a small outfit for their shared customers / users. G43X/49 with RMRcc is approved by many agencies, most of which require red dot pistols be equipped with metallic, co-witnessing backup sights for both on and off duty use. BIS, G43X/48 was created with them in mind. NOTE: If you don't have a sight pusher or the equipment to install rear sights, please bring it to a qualified and competent gunsmith to perform the installation. It's not uncommon to have to fit the rear sight to the dovetail, a competent gunsmith should be well familiar with the reason and method. Forward Controls Design have seen more than enough expensive muzzle devices ruined by "gunsmiths" that used a screw driver to install them instead of a torque wrench, and hand tightened optics plate screws when a torque value is clearly noted in multiple places. Rather than being loose (easy to install), Forward Controls Design prefer the sights be tight, so it won't be knocked off zero easily. Tolerances of the dovetail and sights also come into play, which results in some being easier, while others are harder to install. A qualified gunsmith can deal with these easily.
Scopri il Backup Iron Sight W/Tritium per Glock G43X/G48
Il BIS, G43X/48 (Backup Iron Sight, G43X/G48) è una collaborazione tra Ameriglo e FCD. Specificamente progettato per Glock G43X e G48, questi mirini sono basati sul superbo Ameriglo GL-527, con un'altezza del mirino anteriore di 0.450" e un'altezza del mirino posteriore di 0.554". Questo set di mirini offre un co-witness inferiore a 1/3 con il Trijicon RMRcc quando utilizzato con l'OPF-G43X/43, RMRcc su G43X e G48.
Caratteristiche del prodotto:
- Mirino anteriore: disponibile con Tritium verde e contorno bianco (senza seghettature), oppure mirino anteriore seghettato, senza tritium o contorno bianco.
- Mirino posteriore: seghettato.
Il BIS, G43X/48 presenta alcune differenze rispetto al GL-527 su cui è basato. Le modifiche specifiche di FCD includono:
- Opzione Tritium per il mirino anteriore.
- L'angolo del supporto posteriore del mirino anteriore è più ripido (25 gradi per il mirino anteriore seghettato e non tritium, 20 gradi per il mirino anteriore non seghettato e con tritium) per ridurre l'attrito quando la pistola viene estratta dalla fondina, dove è probabile che incontri indumenti. Gli angoli superiori del mirino anteriore sono smussati.
- Il mirino posteriore è seghettato orizzontalmente.
Progettato e realizzato negli Stati Uniti. Un ringraziamento speciale ai professionisti di Ameriglo che hanno reso possibile questo progetto; Forward Controls Design è grato per la loro disponibilità a collaborare con una piccola azienda per i loro clienti/utenti condivisi. G43X/49 con RMRcc è approvato da molte agenzie, la maggior parte delle quali richiede che le pistole dotate di punto rosso siano dotate di mirini metallici di backup co-witness sia per l'uso in servizio che fuori servizio. Il BIS, G43X/48 è stato creato tenendo conto di queste esigenze.
Nota: Se non possiedi un pusher per mirini o l'attrezzatura per installare i mirini posteriori, ti preghiamo di rivolgerti a un armaiolo qualificato e competente per eseguire l'installazione. Non è raro dover adattare il mirino posteriore alla dovetail; un armaiolo competente dovrebbe essere ben familiare con il motivo e il metodo. Forward Controls Design ha visto più che abbastanza dispositivi di bocca costosi rovinati da "armaioli" che hanno utilizzato un cacciavite per installarli invece di una chiave dinamometrica, e hanno serrato a mano le viti della piastra ottica quando un valore di coppia è chiaramente indicato in più posti.
Piuttosto che essere allentati (facile da installare), Forward Controls Design preferisce che i mirini siano serrati, in modo che non vengano facilmente disallineati. Le tolleranze della dovetail e dei mirini giocano anche un ruolo, il che porta alcuni a essere più facili, mentre altri sono più difficili da installare. Un armaiolo qualificato può gestire questi aspetti con facilità.