Replaces the grip on the right side of Colt-Style semi-auto frame so it can't interfere with thumb safety operation. "Quad Lock" installation system securely attaches the mount to the frame at four points. Accepts Weaver-style rings. No drilling or tapping. Cannot be used with ambidextrous safety or ambidextrous slide release.
SPECS: Black-anodized, extruded aluminum. Approx. 5-1/2" long, 6" (15.2cm) high. Includes mounting pins and instructions. Cannot be used with ambidextrous safety or ambidextrous slide release.
Altro...
Leggero, "Lato destro" Scope Mount
Sostituisce il grip sul lato destro del telaio semi-automatica Colt-stile in modo che non può interferire con il funzionamento di sicurezza del pollice. Sistema di installazione "Quad Lock" si attacca saldamente il supporto al telaio in quattro punti. Accetta gli anelli Weaver-stile. Nessuna foratura o toccando. Non può essere utilizzato con sicurezza ambidestro o rilascio ambidestro diapositiva.
SPECIFICHE: In alluminio estruso, anodizzato nero. Circa 5-1/2" lungo, alti 6" (15,2 cm). Include le istruzioni e perni inferiori. Non può essere utilizzato con sicurezza ambidestro o rilascio ambidestro diapositiva.
Altro...
Punteggi dei clienti per AIMTECH 1911 GRIP PANEL SCOPE MOUNT
Numero di punteggi: 3
Da brownells.com: 3
Punteggio medio: 1,7
Good unit but not for competition(14/08/2009)
My wife could not hit anything with my iron sited Gold Cup. I installed this with red-dot site and all of a sudden she was hitting the target. Had to file a very small amount off the right side of the iron site for the slide to be removed for cleaning. I had a very accurate mild load that I have used for 30 years with this gun and with the extra mass it had some cycle problems, but I upped the load by .1 grains and all is well. Still accurate and it cycles good. Not for serious target work, but it is accurate.
It has very close tolerances in the alignment of the 2 threaded rods that bolt it in place, take your time or you will strip the threads. Other wise it is easy to install.
Ejection nightmare(29/09/2012)
When it arrived in the mail I was surprised to see it went on the right hand side of my Pistol. I put this on my standard gov issue M1911A1. I just knew there was going to be ejection problems, but being the optimist I tried it out. Sure enough it jammed on every ejected case. It was a complete waste of money.
Replaces the grip on the right side of Colt-Style semi-auto frame so it can't interfere with thumb safety operation. "Quad Lock" installation system securely attaches the mount to the frame at four points. Accepts Weaver-style rings. No drilling or tapping. Cannot be used with ambidextrous safety or ambidextrous slide release.
SPECS: Black-anodized, extruded aluminum. Approx. 5-1/2" long, 6" (15.2cm) high. Includes mounting pins and instructions. Cannot be used with ambidextrous safety or ambidextrous slide release.
Altro...
Leggero, "Lato destro" Scope Mount
Sostituisce il grip sul lato destro del telaio semi-automatica Colt-stile in modo che non può interferire con il funzionamento di sicurezza del pollice. Sistema di installazione "Quad Lock" si attacca saldamente il supporto al telaio in quattro punti. Accetta gli anelli Weaver-stile. Nessuna foratura o toccando. Non può essere utilizzato con sicurezza ambidestro o rilascio ambidestro diapositiva.
SPECIFICHE: In alluminio estruso, anodizzato nero. Circa 5-1/2" lungo, alti 6" (15,2 cm). Include le istruzioni e perni inferiori. Non può essere utilizzato con sicurezza ambidestro o rilascio ambidestro diapositiva.
Altro...
Punteggi dei clienti per AIMTECH 1911 GRIP PANEL SCOPE MOUNT
Numero di punteggi: 3
Da brownells.com: 3
Punteggio medio: 1,7
Good unit but not for competition(14/08/2009)
My wife could not hit anything with my iron sited Gold Cup. I installed this with red-dot site and all of a sudden she was hitting the target. Had to file a very small amount off the right side of the iron site for the slide to be removed for cleaning. I had a very accurate mild load that I have used for 30 years with this gun and with the extra mass it had some cycle problems, but I upped the load by .1 grains and all is well. Still accurate and it cycles good. Not for serious target work, but it is accurate.
It has very close tolerances in the alignment of the 2 threaded rods that bolt it in place, take your time or you will strip the threads. Other wise it is easy to install.
Ejection nightmare(29/09/2012)
When it arrived in the mail I was surprised to see it went on the right hand side of my Pistol. I put this on my standard gov issue M1911A1. I just knew there was going to be ejection problems, but being the optimist I tried it out. Sure enough it jammed on every ejected case. It was a complete waste of money.