Trims Away The Last "Whisker" For A Squared-Up Sight Installation
No more tilted, sloppy looking, half square front sight beads. Faces-off the base of "Bradley"-style (Bev-L-Blok, Raybar, Sunspot, etc.) beads so they end up straight and square to the center of the rib or barrel when tightened. Six-bladed cutter with precisely drilled hollow center accepts bead shank. Turning the handle trims base of the bead at a true 90° angle that's absolutely square with the shank.
SPECS: Six blade cutter, high speed steel, 3½" (8.8cm) long, 1-1/8" (2.8cm) diameter handle.
Altro...
Taglia via l'ultimo "Baffo" per un'installazione di vista squadrato-Up
Sciatta, non più inclinato alla ricerca, metà perline quadrato mirino. Facce-fuori la base di perline "Bradley" stile (Bev-L-Blok, Raybar, macchie solari, ecc.) così finire dritto e quadrato al centro della costola o barile quando serrate. Taglierina a sei pale con centro cava precisamente forato accetta tibia del tallone. Girando la maniglia coprifili base del tallone con un angolo di vera 90° che è assolutamente quadrato con la tibia.
Specifiche: sei lame in acciaio ad alta velocità, 3½"(8,8 cm) lungo, 1-1/8" manico di diametro (2,8 cm).
Altro...
Punteggi dei clienti per BROWNELLS #6 STD SHANK SHOTGUN BEAD FACING CUTTER .140" DIAMETER
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 4,5
Does What It is Designed to Do(13/09/2012)
Used this tool as a result of a Guntech recommendation to properly index a Meprolight Mossberg 5-40 threaded tritium bead. The #6 intended for 6-48 beads, worked like a champ on the 5-40 threaded shank.
Good tool(15/01/2015)
Used this installing a front bead that needed to be indexed. Wasn't sure if I would need it or not but I am very glad I ordered it. When I first installed my sight I was probably 300 degrees from where I needed. Used this to shave the bottom until it was just snug with about 90 degrees to go. I would have certainly snapped the small 3-56 screw off in the hole had I not had this tool. Highly recommend, if you need it, you NEED it. Only bad part is I probably won't use it again for a very long time.
N. prodotto: 080517006 BROWNELLS #6 STD SHANK SHOTGUN BEAD FACING CUTTER .140" DIAMETER Sciatta, non più inclinato alla ricerca, metà perline quadrato mirino. Facce-fuori la base di perline "Bradley" stile (Bev-L-Blok, Raybar, macchie solari, ecc.) così finire dritto e quadrato al centro della costola o barile quando serrate. Taglierina a sei pale con centro cava precisamente forato accetta tibia del tallone. Girando la maniglia coprifili base del tallone con un angolo di vera 90° che è assolutamente quadrato con la tibia.
47.9EUR047,90 €
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
N. prodotto: 080517003 BROWNELLS #3 SHANK SHOTGUN BEAD FACING CUTTER .099" DIAMETER Parti Fabbricante: 3BEADCUTTER Sciatta, non più inclinato alla ricerca, metà perline quadrato mirino. Facce-fuori la base di perline "Bradley" stile (Bev-L-Blok, Raybar, macchie solari, ecc.) così finire dritto e quadrato al centro della costola o barile quando serrate. Taglierina a sei pale con centro cava precisamente forato accetta tibia del tallone. Girando la maniglia coprifili base del tallone con un angolo di vera 90° che è assolutamente quadrato con la tibia.
59.9EUR559,90 €
*
Tempi di consegna circa 14-21 giorni. 5 pz. nel magazzino USA
N. prodotto: 080517008 BROWNELLS #8 SHANK SHOTGUN BEAD FACING CUTTER .166" DIAMETER Sciatta, non più inclinato alla ricerca, metà perline quadrato mirino. Facce-fuori la base di perline "Bradley" stile (Bev-L-Blok, Raybar, macchie solari, ecc.) così finire dritto e quadrato al centro della costola o barile quando serrate. Taglierina a sei pale con centro cava precisamente forato accetta tibia del tallone. Girando la maniglia coprifili base del tallone con un angolo di vera 90° che è assolutamente quadrato con la tibia.
48.9EUR348,90 €
*
Tempi di consegna circa 14-21 giorni. 3 pz. nel magazzino USA
Trims Away The Last "Whisker" For A Squared-Up Sight Installation
No more tilted, sloppy looking, half square front sight beads. Faces-off the base of "Bradley"-style (Bev-L-Blok, Raybar, Sunspot, etc.) beads so they end up straight and square to the center of the rib or barrel when tightened. Six-bladed cutter with precisely drilled hollow center accepts bead shank. Turning the handle trims base of the bead at a true 90° angle that's absolutely square with the shank.
SPECS: Six blade cutter, high speed steel, 3½" (8.8cm) long, 1-1/8" (2.8cm) diameter handle.
Altro...
Taglia via l'ultimo "Baffo" per un'installazione di vista squadrato-Up
Sciatta, non più inclinato alla ricerca, metà perline quadrato mirino. Facce-fuori la base di perline "Bradley" stile (Bev-L-Blok, Raybar, macchie solari, ecc.) così finire dritto e quadrato al centro della costola o barile quando serrate. Taglierina a sei pale con centro cava precisamente forato accetta tibia del tallone. Girando la maniglia coprifili base del tallone con un angolo di vera 90° che è assolutamente quadrato con la tibia.
Specifiche: sei lame in acciaio ad alta velocità, 3½"(8,8 cm) lungo, 1-1/8" manico di diametro (2,8 cm).
Altro...
Punteggi dei clienti per BROWNELLS #6 STD SHANK SHOTGUN BEAD FACING CUTTER .140" DIAMETER
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 4,5
Does What It is Designed to Do(13/09/2012)
Used this tool as a result of a Guntech recommendation to properly index a Meprolight Mossberg 5-40 threaded tritium bead. The #6 intended for 6-48 beads, worked like a champ on the 5-40 threaded shank.
Good tool(15/01/2015)
Used this installing a front bead that needed to be indexed. Wasn't sure if I would need it or not but I am very glad I ordered it. When I first installed my sight I was probably 300 degrees from where I needed. Used this to shave the bottom until it was just snug with about 90 degrees to go. I would have certainly snapped the small 3-56 screw off in the hole had I not had this tool. Highly recommend, if you need it, you NEED it. Only bad part is I probably won't use it again for a very long time.