Il Carrello è vuoto.

Carrello

0364 1955 195

BROWNELLS .146x48 OVERSIZE 6-48 SCREW SHOP KIT

Traduzione automatica (Descrizione originale - Produttore): 1 viti di. Altro...

080719212

Saves Your "Tail Feathers" If A Hole Gets Stripped

Slightly larger in diameter than the common 6-48 scope base mounting screw. Most holes "ruined" while drilling or tapping can be fixed; just retap to .146"-48 and install. No need to redrill base or gun. Thanks to Doug Knowt for his tip. Click Here for taps.

SPECS: .146"-48x½" (12.7mm) slotted machine screws, blued finish. Fillister and Weaver-style head. Kit contains 48 of each style, 1 taper tap, 1 bottom tap, and 1 Screw Gizzie in a bench box.

Altro...

Salva il tuo "piume della coda" se ottiene spogliato un buco

Leggermente più grande di diametro di comune scopo 6-48 vite di montaggio della base. La maggior parte fori "rovinato" mentre foratura o toccando può essere fissato; solo retap.146"-48 e installazione. Nessuna necessità di riforare base o pistola. Grazie Doug Knowt per il suo suggerimento. Clicca qui per i rubinetti.

Specifiche:.146"-48x½" a macchina con intaglio viti azzurrate finitura (12,7 mm). Testa cilindrica e stile Weaver. Il kit contiene 48 di ogni stile, 1 sbozzatore, rubinetto 1 inferiore e 1 vite Gizzie in una scatola di panca.

Altro...

Punteggi dei clienti per 1 Dz. Weaver .146"-48 Screws

Numero di punteggi: 7
Da brownells.com: 7
Punteggio medio: 4,9

Saves a job gone bad! (05/09/2010)

8-40 Torx screws into a Remington 1100 stripped out the receiver. These screws, combined with the .146"-48 tap worked perfectly! As noted in tips description by Mr. Doug Knowt, no need to re-drill. Just run the tap through, install the oversize screws, and your done! The screw heads were exact size as Torx, and the screws were plenty long enough to grind to fit any application. Thanks Brownell's! Thanks Mr. Knowt!

Just the ticket! (01/07/2016)

I used these in conjunction with the required tap to fix the scope base screw holes in a Remington 597 receiver. The screw holes were a bit oversized as it came from the factory with only .002" of thread engagement.

Excellent fix! - almost perfect (14/06/2018)

I used these in conjunction with the associated tapered tap to fix the scope base screw holes in a Remington 700 receiver. The front two screws from the factory were stripped and would just spin. I had to drive them down through the holes after removing the barrel. The tapered tap did its' job by hand. Used the tap and a 1/8" drill bit on a piece of O-1 steel to allow me to cut and file the screws down to size. The only issue with these screws is the slotted head. My Burris XTR steel scope base calls for 35 in lbs of torque and the little slotted screw head wouldn't hold the bit all of the way to 35 in lbs of torque. A socket head or torx head would do the trick and would have made this solution perfect. Very happy overall though, I recommend this solution for stripped receiver scope base holes.

Receiver saver! (14/04/2011)

This kit was great and easy to use. A friend and I purchased after both had stripped out screws on Ruger 10/22 receivers. Bought this kit and the proper drill bit. Shortly after had new threaded holes in the receiver and scope rails mounted, with much less torque this time. Used Brownells video on how to make a screw jig from flat stock instead of using the gizzie. Have fixed 3 other receivers for a buddy at the local gun shop and more than paid for the kit.

Great kit for 10/22 (14/07/2014)

This kit made fixing stripped holes in a 10/22 receiver

a snap! Thanks Brownell's.

Simple to use. (12/03/2016)

I used the kit to repair a Ruger 10-22 with a stripped scope mount/receiver screw. I only fixed the damaged screw hole. (Hey, if it isn't broke, don't fix it) The Kit comes with 2 taps, one gizzy and a bunch of screws. Useless instructions. The tap with a point is the taper tap, and you use it for holes that go all-the-way through, and you use it to start all holes because you need the pointed end to initiate the holes. The bottom tap is the one with the blunt end. You would use it for holes that do not go completely through. Again, start with the pointed tap. The kit does not come with a handle, so I bought a cheap 3-piece kit from Harbor Freight for $7.00. I clamped my receiver in a padded vise, made it as level as I could, sprayed a bit of WD-40 on the tap and in the receiver screw hole, and turned it in by hand with the taper tap. Easy as pie. The Gizzy wasn't threaded, so I ran the taper tap through the small hole on the gizzy, and then threaded one of the screws in until it was about the same length as my factory scope mount screws. I didn't measure it (I should have). About a minute on my grinder, and I checked the fit of the screw using the scope mount and 10-22 receiver. Make sure the screws don't extend too far into the receiver, because the bolt with make contact with it. Overall, it's a pretty simple kit, and I don't have to ship the gun back to Ruger or take it to a gun smith. They include enough screws to repair a few dozen rifles. According to Ruger, don't use Loc tite on the 10-22. Evidently, it adds a bit of pressure, and is the cause of countless stripped receivers. Good luck.

Excellent!! (06/04/2017)

Purchased a 541S at the local gun shop,not realizing three of the four base holes were stripped until trying to mount a base..This kits bottoming tap and the included oversize screws(after shortening to length) saved the day..Worked perfect,worth every penny. Thanks Brownells!

Leggi più recensioni su brownells.com

5.7 110 3 EUR

080719212
1 Dz. Weaver .146"-48 Screws
Parti Fabbricante: 89164 1 viti di.146"-48 Weaver DZ.

5.7 EUR 0 5,70 € *

Avvisa quando diventa disponibile

Al momento non è possibile acquistare o riservare questo prodotto.

Aggiungi alla lista degli acquisti

Domande

Dettagli

Aggiungi alla lista degli acquisti

Domande

Descrizione

1 viti di.146"-48 Weaver DZ.

Dettagli dell'elemento

Made in Usa

080719000
.146"-48 Shop Kit .146"-48 negozio Kit

110 EUR 0 110,00 € *

Avvisa quando diventa disponibile

Acquista in backorder da magazzino Brownells USA - Il prodotto verrà spedito quando sarà nuovamente disponibile

Aggiungi alla lista degli acquisti

Domande

Dettagli

Aggiungi alla lista degli acquisti

Domande

Descrizione

.146"-48 negozio Kit

Dettagli dell'elemento

Made in Usa

080719112
1 Dz. Fillister .146"-48 Screws
Parti Fabbricante: 89165 1 viti di.146"-48 cilindrica DZ.

8.1 EUR 0 8,10 € *

Avvisa quando diventa disponibile

Al momento non è possibile acquistare o riservare questo prodotto.

Aggiungi alla lista degli acquisti

Domande

Dettagli

Aggiungi alla lista degli acquisti

Domande

Descrizione

1 viti di.146"-48 cilindrica DZ.

Dettagli dell'elemento

Made in Usa

Saves Your "Tail Feathers" If A Hole Gets Stripped

SPECS: .146"-48x½" (12.7mm) slotted machine screws, blued finish. Fillister and Weaver-style head. Kit contains 48 of each style, 1 taper tap, 1 bottom tap, and 1 Screw Gizzie in a bench box.

Altro...

Salva il tuo "piume della coda" se ottiene spogliato un buco

Altro...

Punteggi dei clienti per 1 Dz. Weaver .146"-48 Screws

Numero di punteggi: 7
Da brownells.com: 7
Punteggio medio: 4,9

Saves a job gone bad! (05/09/2010)

Just the ticket! (01/07/2016)

Excellent fix! - almost perfect (14/06/2018)

Receiver saver! (14/04/2011)

Great kit for 10/22 (14/07/2014)

This kit made fixing stripped holes in a 10/22 receiver

a snap! Thanks Brownell's.

Simple to use. (12/03/2016)

Excellent!! (06/04/2017)

Leggi più recensioni su brownells.com

Scelti da altri clientie

#4 Refill Pak
PREMIUM GRINDING POINT KIT

BROWNELLS

Prenotabile Acquista in backorder da magazzino Brownells USA - Il prodotto verrà spedito quando sarà nuovamente disponibile

13,30 € * 13,10 € - 61,90 €*

Fresette | Pietre abrasive

0 (0)

#5 Roll Pin Punch
ROLL PIN PUNCHES

BROWNELLS

Disponibile +10 disponibili presso il magazzino Brownells USA

9,90 € * 8,70 € - 45,20 €*

Punzoni

3,4 (20)

Front Sight Pusher

WILLIAMS GUN SIGHT

Disponibile 9 disponibili presso il magazzino Brownells USA

96,20 € * 20,90 € - 96,20 €*

Strumenti regolazione mire

3,1 (7)

SS Roll Pin Kit
STAINLESS STEEL ROLL PIN KIT

BROWNELLS

Prenotabile Acquista in backorder da magazzino Brownells USA - Il prodotto verrà spedito quando sarà nuovamente disponibile

112,60 € * 4,60 € - 112,60 €*

Spine cilindriche

0 (0)

.060" Rod, 3-Pak
FIBER OPTIC SIGHT RODS

MOUNTING SOLUTIONS PLUS

Esaurito Al momento non è possibile acquistare o riservare questo prodotto.

36,60 € * 11,30 € - 36,60 €*

Inserti ricambio mire

5 (1)

Accesso

Hai dimenticato la password?
Registrati

Social Media

Brownells.it

Catalogo prodotti

Ordinare

Customer Service

Benvenuti!

Benvenuti su Brownells.it, il principale rivenditore online di accessori per armi da fuoco, componenti di pistole e utensili per armaioli in Italia!

La nostra offerta

Se ti piace sparare, lavorare sulle armi da fuoco come artigiano o per hobby, o semplicemente possiedi un'arma, questo è il posto per te!

Grazie alla nostra grande esperienza, ogni giorno, tiratori, armaioli professionisti, hobbisti, militari, esponenti delle forze dell'ordine e appassionati d'armi si rivolgono a Brownells.it per trovare accessori e componenti di alta qualità e fare rifornimento di ciò di cui hanno bisogno.

Nel nostro negozio online potrai trovare oltre 60.000 prodotti, tra cui parti d'arma, accessori, utensili per armieri, materiale per ricarica e componenti di munizioni, e altri prodotti per mantenere, riparare e aggiornare le tue armi.