Fluorescent green, combat-style follower with projection on the head, instantly shows by sight, or by touch, if mag is empty. Molded from non-rusting, high-impact grade ABS with tapered tail to help prevent magazine spring bind and improve reliability.
SPECS: 1.7" (4.5cm) long, .91" (23mm) diameter. 12 ga. only. Fits Remington 870, 1100 and other miscellaneous shotguns with no detents in magazine tube.
Altro...
Follower di colore verde fluorescente, in stile combattimento, con una sporgenza sulla testa che mostra immediatamente, sia visivamente che al tatto, se il caricatore è vuoto. Realizzato in ABS ad alto impatto e non soggetto a ruggine, con coda affusolata per aiutare a prevenire l'inceppamento della molla del caricatore e migliorare l'affidabilità.
SPECIFICHE: Lunghezza 1.7" (4.5cm), diametro .91" (23mm). Solo calibro 12. Compatibile con Remington 870, 1100 e altri fucili vari con tubo del caricatore senza rientranze.
Altro...
Punteggi dei clienti per SCATTERGUN TECHNOLOGY REMINGTON 870 MAGAZINE FOLLOWER, 12 GA.
Numero di punteggi: 8
Da brownells.com: 8
Punteggio medio: 3,6
= one less(15/01/2011)
Terrible design! Limits the tube capacity by one round, deforms slightly in the tube and then binds as it moves towards the receiver.
Edgard Villa(20/03/2011)
Will fit some newer Remington 870 only with some minor "Dremel" fitting.
Works great!(16/05/2011)
This works great in my 870. I removed the dimples as I added a mag. tube extension. I have had no issues in several hundred rounds. It is solid and made of a tough plastic, not some brittle cheap feeling material. I am sure it will wear very well. The extended "tail" keeps it aligned properly in the spring. It doesn't limit my capacity of 2 3/4" shells.
Magazine Follower Doesn't Follow(28/10/2011)
This binded in the tube after running a single test round through it. Had to knock it free with a screwdriver. Complete waste of the money; glad there's nothing wrong with my original follower.
Good item(15/01/2012)
Use in my 870, Buying another for my 1100. Hi-vis to see magazine is empty at a glance, and acts as a spring guide when spring is fully compressed. There is a reason why expensive mod. kits/shotguns come with this follower.
pro and con(21/04/2015)
all is good with this follower except for the loss of one round in my extended magazine ( went from 7 plus one to 6 plus one), but i think if i cut and file off about half inch from the tail section of the follower, should get back my seventh round. great color and feel on empty mag.
Magazine tube extension(09/06/2016)
I installed a 5 rd mag extension on my 870 and replaced the factory follower with this. One problem. the back edge was "too sharp" to pass where the detents had been. So, I took my Dremel and ground down the edge at an angle about an eighth of an inch. Works perfectly now!
Love it(21/07/2017)
Nicely priced, the product itself is solid. I have an 870 express mag with dimples still on the tube (4shot), 5 minutes with a rounded file and the follower fell in without issue. Still have plenty of room in the tube and retain 4 shells in the mag.
N. prodotto: 800100004 SCATTERGUN TECHNOLOGY REMINGTON 870 MAGAZINE FOLLOWER, 12 GA. Parti Fabbricante: SGHVF683507710193 Follower di colore verde fluorescente, in stile combattimento, con una sporgenza sulla testa che mostra immediatamente, sia visivamente che al tatto, se il caricatore è vuoto. Realizzato in ABS ad alto impatto e non soggetto a ruggine, con coda affusolata per aiutare a prevenire l'inceppamento della molla del caricatore e migliorare l'affidabilità.
19.9EUR1419,90 €
*
Tempi di consegna circa 12-16 giorni. Più di 10 pz. nel magazzino USA
Fluorescent green, combat-style follower with projection on the head, instantly shows by sight, or by touch, if mag is empty. Molded from non-rusting, high-impact grade ABS with tapered tail to help prevent magazine spring bind and improve reliability.
SPECS: 1.7" (4.5cm) long, .91" (23mm) diameter. 12 ga. only. Fits Remington 870, 1100 and other miscellaneous shotguns with no detents in magazine tube.
Altro...
Follower di colore verde fluorescente, in stile combattimento, con una sporgenza sulla testa che mostra immediatamente, sia visivamente che al tatto, se il caricatore è vuoto. Realizzato in ABS ad alto impatto e non soggetto a ruggine, con coda affusolata per aiutare a prevenire l'inceppamento della molla del caricatore e migliorare l'affidabilità.
SPECIFICHE: Lunghezza 1.7" (4.5cm), diametro .91" (23mm). Solo calibro 12. Compatibile con Remington 870, 1100 e altri fucili vari con tubo del caricatore senza rientranze.
Altro...
Punteggi dei clienti per SCATTERGUN TECHNOLOGY REMINGTON 870 MAGAZINE FOLLOWER, 12 GA.
Numero di punteggi: 8
Da brownells.com: 8
Punteggio medio: 3,6
= one less(15/01/2011)
Terrible design! Limits the tube capacity by one round, deforms slightly in the tube and then binds as it moves towards the receiver.
Edgard Villa(20/03/2011)
Will fit some newer Remington 870 only with some minor "Dremel" fitting.
Works great!(16/05/2011)
This works great in my 870. I removed the dimples as I added a mag. tube extension. I have had no issues in several hundred rounds. It is solid and made of a tough plastic, not some brittle cheap feeling material. I am sure it will wear very well. The extended "tail" keeps it aligned properly in the spring. It doesn't limit my capacity of 2 3/4" shells.
Magazine Follower Doesn't Follow(28/10/2011)
This binded in the tube after running a single test round through it. Had to knock it free with a screwdriver. Complete waste of the money; glad there's nothing wrong with my original follower.
Good item(15/01/2012)
Use in my 870, Buying another for my 1100. Hi-vis to see magazine is empty at a glance, and acts as a spring guide when spring is fully compressed. There is a reason why expensive mod. kits/shotguns come with this follower.
pro and con(21/04/2015)
all is good with this follower except for the loss of one round in my extended magazine ( went from 7 plus one to 6 plus one), but i think if i cut and file off about half inch from the tail section of the follower, should get back my seventh round. great color and feel on empty mag.
Magazine tube extension(09/06/2016)
I installed a 5 rd mag extension on my 870 and replaced the factory follower with this. One problem. the back edge was "too sharp" to pass where the detents had been. So, I took my Dremel and ground down the edge at an angle about an eighth of an inch. Works perfectly now!
Love it(21/07/2017)
Nicely priced, the product itself is solid. I have an 870 express mag with dimples still on the tube (4shot), 5 minutes with a rounded file and the follower fell in without issue. Still have plenty of room in the tube and retain 4 shells in the mag.